Call - 0161 622 0020
Cart 0
FIX UNDERNEATH,RIGHT ANGLED NYLON BRUSH STRIP 10-50 MM TRIM AT CRANKED 90 DEGREE

FIX UNDERNEATH,RIGHT ANGLED NYLON BRUSH STRIP 10-50 MM TRIM AT CRANKED 90 DEGREE

£7.35


PICTURE SHOWS 15 MM 
Please choose the correct size brush you must have a parallel gap to fit these, see chart below 

CRANKED AT 90 DEGREES TO BRUSH A RIGHT ANGLED CARRIER 

Check out my other items!  IN THE CULLEY_FAMILY_SHOP

Regardless of the number of pieces you buy , this product is shipped by a carrier called HERMES They take about 3-5 Working days from despatch of product , if we get busy as we had in November 2013, our despatch date could be slightly longer than 5 working days 

  FOR OLD CUSTOMERS IT IS NOW TOO LONG TO GO BY POST IN LONGER LENGTHS!

We are able to ship this item only to British Post Codes EXCLUDING CHANEL ISLES AND OUTER ISLANDS PLEASE RING 0161 622 0020  FOR CARRIAGE COST 


THESE ARE MADE FULL FILL & MADE WITH GENUINE NYLON 6 FILAMENTS,

PER 0.89 METRE (35 inches in old money if you were in my class )


Draught Proof now before winter, during winter or after winter  Keep all the MICE and dirt/ leaves out as well as draughts

Seals by Culley, called Thehairyworm Premier 90 DEGREE Strip

  

These are made and supplied at 890 mm long (In old money, the size is 35 inches or 2 ft 11")


TECHNICAL ADVICE  0161 622 0020 


We make them this length to allow you to easily trim the carrier and brush to the correct sizes to suit your door, 

Multiple lengths can be used side by side with little loss of sealing benefit. 


(Whilst this range seal up to 48 mm, we do make bigger premier strip @ 90 degree and hve a full range of 180 degree listed elsewhere and make a thicker industrial range from 25 to 150 mm) 


 

10 mm size is for fine draught proofing from 7- 8 mm gaps (we also make smaller seals)

15 mm size is for fine draught proofing from 10- 13 mm gaps

22 mm size is for fine draught proofing from 15 - 20 mm gaps

35 mm size is for fine draught proofing from 28 - 33 mm gaps

50 mm size is for fine draught proofing from 43 - 48 mm gaps


TIP: for church style doors if you are taking them off~ You may have a worn stone step 50 mm is a good answer to this problem but it may make door a little tight initially TILL THE BRUSH SETTLES IN ON THE STEP

 

WE CAN GO BIGGER , PLEASE ASK ! 

 

THIS IS A UK MADE PRODUCT AND IS USED BY DOOR REPAIR COMPANIES AND GENERAL INDUSTRY

 

Garage doors : this can be made into a kit by buying more 890 mm lengths. It can still go by the economical route of: MYHERMES

Subject to the number of lengths it will fit down the bottom of an up and over garage door, with the brush on the outside, we suggest this because if you fit a brush on the front of a garage door as you lift the door (or the motor lifts a door) the filaments pull off the floor, if you fit it on the rear of the garage door , the brush is further swept tightening into the floor , straining all the door and also, if fitted your motor. The other point is any rubbish blown under your door is blown into the garage.


 ie Buy 3 Pieces @ 890 mm DOWN THE BOTTOM OF AN UP AND OVER GARAGE DOOR) WITH THIS KIT IT WILL SEAL FROM 2.00 METRES UP TO 2.670 METRES ,  (6  FEET  TO 8 FEET 9 “ wide ) 


ie Buy 4 Pieces @ 890 mm DOWN THE BOTTOM OF AN UP AND OVER GARAGE DOOR) WITH THIS KIT IT WILL SEAL FROM 2.00 METRES UP TO 3.560 METRES ,  (9  FEET to TO 11 FEET  8"   wide ) and so on ........ 


It is easy to fit , just follow the simple instructions included , then THEHAIRYWORM PREMIER 90 Will give you a long life.


 IF YOU NEED OTHER SIZES PLEASE ASK, OTHER TRIMS ON OUR CULLEY_FAMILY_SHOP

  

This correctly made brush strip is not an import; this is made in the UK with pride

 

MATERIALS:

We make a full fill brush with the right components. This is our 4 mm series backing width brush  Our brushes are made of nylon 6 an important factor we feel.

 

The carrier is made from architectural aluminium a point worth noting, it makes the carrier stronger, its overall height of the flat part of the "h" holder is 16 mm, the trim of brush is measured out of the steel backing inside the aluminium on this sizing giving about 2 mm of bristle less on all sizes out of the aluminium holder.


For the technically minded:

Nylon 6 is a harder wearing material against concrete and other hardwearing surfaces than polypropylene 

Nylon 6 has a higher working temperature of about 145 degrees centigrade, Polyproylene softens far earlier than this.

We do not use Polypropylene but competitors do , it softens at 70 – 80 degrees centigrade. This is a temperature your garage door reaches when it gets warm in the summer , when warm polypropylene bristles then bend and stays bent causing the brush to appear to move away from its opposing surface, as they cool they stay the same size curled not touching the opposite side 

I will leave you to decide which is the right choice , I will say chalk and cheese!  


(A lot of competitors use this and also partial fill! to make brushes lower in cost for them! We dont short change.

WE ONLY SELL FULL FILL BRUSHES 

 

The brush strip should only be fitted to the outside of an up and over door , as the rear of the door dips slightly upon lifting , if you put a brush or any seal on the bottom ,it will catch and scrap causing the door to judder on opening , a problem if you have motor driven doors.

 

This item is suitable for draught proofing , dust  sealing , dust sealing , insect sealing , stops flies , stops moths , cockroaches & yes they are in the UK, aluminium,timber ,steel , PVCu, GRP  doors,

 

 Cuts easily with top hardened cutters, or good pincers and junior hacksaw, comes with full fitting instructions, you need to follow the full instructions 

 

WE DO NOT SUPPLY SCREWS AS WE KNOW DIFFERENT SURFACES REQUIRE DIFFERENT FIXINGS AND DIFFERENT COLOURS, AGAIN WE DO NOT DRILLTHE PRODUCT AS ALL THE HOLES WILL NOT LINE UP WITH YOUR DOOR.

 

We have also developed and have on sale FLEXIBLE  "the hairy worm" seal to go up the sides of an up and over door ,please look on our shop~ CHECK THIS OUT ! 

 

Culley’s also stock a large range of other style draught excluders, brush strips & weather strip products and also trade rubber extrusions.

 

Please enquire:  Via e bay questions:

For correct advice for help sealing other styles of windows or doors; we solve 95% of problems with draught invasion! Our product offers money saving where heating takes place.

DON’T HEAT THE STREET, SAVE IT!!! ITS YOUR MONEY 

If you require more info please contact me on: 0161 622 0020


Share this Product


More from this collection